DSPIC30F4012 v230 Source Code

[moodz]

I received my Pickit2 Clone today from Sure Electronics. It did not come w/software. I downloaded the MPLAB C Compiler from here: http://www.microchip.com/stellent/id...cName=en536656

Dave Frank

If you are only burning the hex files and want to use the inbuilt UART tool ( serial comms ) to talk to the UNIP chip ( saves wiring up an LCD ) get the pickit software here ....

http://ww1.microchip.com/downloads/e...0Setup%20A.zip

Regards moodz.

[6666]

Thanks moodz and dave
mine came with no software
it is supposed to work with mplab I have version 8.76
you need a version above 8.2

the handbook for this pickit 3 is at
http://www.sure-electronics.net/down...B-DP005&type=0

just click the word download

trying to get the pc to talk to it
cheers

and the LCD arrived in the mail

[6666]

Sorry to hijack your thread
been trying to get the pc to talk to the pickit 3
with mplab.

Seems to be a plug and play setup
plug in the pickit3 to usb port
start up mplab and select programmer or debugger (pickit3)
but keep getting this error message

PICkit 3 detected
Connecting to PICkit 3...
PK3Err0038: Failed to initialize PICkit 3.

Has anybody else got one of these pickit3 clones to work ?
there does not seem to be any other settings to pick from
thanks

[moodz]

Sorry to hijack your thread
been trying to get the pc to talk to the pickit 3
with mplab.

Seems to be a plug and play setup
plug in the pickit3 to usb port
start up mplab and select programmer or debugger (pickit3)
but keep getting this error message

PICkit 3 detected
Connecting to PICkit 3...
PK3Err0038: Failed to initialize PICkit 3.

Has anybody else got one of these pickit3 clones to work ?
there does not seem to be any other settings to pick from
thanks

Try connecting the PICkit 3 to a board with a chip to be programmed on it.
OR
You could try the following procedure ...
Run MPLAB then hold the button on the unit, and while holding, plug into the USB. This will reload the firmware however I am not sure it will work for clones.

regards,

moodz.

[moodz]

Try connecting the PICkit 3 to a board with a chip to be programmed on it.
OR
You could try the following procedure ...
Run MPLAB then hold the button on the unit, and while holding, plug into the USB. This will reload the firmware however I am not sure it will work for clones.

regards,

moodz.

OR try this .... from a Microchip thread...

1 - Open MPLAB 8.3 or 8.36 - I'm not really sure why, but it is this one that has PK3FW_012505.jam firmware and select PK3 programmer (Programmer -> Select Programmer);
2 - Connect PICkit3, you'll get the error 38 or so, stating that PIC is not connected;
3 - Press the button on PK3, until the blue Active light starts blinking;
4 - Go to Programmer -> Settings -> Configuration and press the Manual Download button;
5 - Choose PK3FW_012505.jam firmware and press Open;

moodz.

[6666]

Thank you moodz
I have tried the first two ideas no joy
so downloading ver 8.3
and will give that a try
much appreciated
6666

[mickstv]

Thank you moodz
I have tried the first two ideas no joy
so downloading ver 8.3
and will give that a try
much appreciated
6666

I've been looking at that ebay site and the pictures of the PICkit 3 and the PICkit 2 are identical I wonder whether it's a PICkit 2 in disguise. Have you tried MPlab and running it as PICkit 2 ?




Mick

[moodz]

I've been looking at that ebay site and the pictures of the PICkit 3 and the PICkit 2 are identical I wonder whether it's a PICkit 2 in disguise. Have you tried MPlab and running it as PICkit 2 ?




Mick

Also try connecting via a powered USB hub ... not direct to PC ... some PK3s need more juice.

moodz

[ApBerg]

http://www.geotech1.com/forums/showt...875#post135875

best regards.

Ap

[6666]

Hi all
thanks for all the ideas
have tried them all, but no joy
I am now onto shure electronics
to see if they can help me to get it to work
might be a dud

[Qiaozhi]

Hi all
thanks for all the ideas
have tried them all, but no joy
I am now onto shure electronics
to see if they can help me to get it to work
might be a dud

http://www.geotech1.com/forums/showp...75&postcount=3

[6666]

Sorry Moodz for thread hijack, I got the pickit3 working now on another pc
back to your project .
6666

[6666]

My project has ground to a halt, caught between a rock and a hard place
I paid for my 4012 chips on the 21 sept and according to tracking number
they have not left the usa yet and its now the 13th of Oct
Avoid an fleabay seller called audiosector they are very very slow posters.

[mickstv]

My project has ground to a halt, caught between a rock and a hard place
I paid for my 4012 chips on the 21 sept and according to tracking number
they have not left the usa yet and its now the 13th of Oct
Avoid an fleabay seller called audiosector they are very very slow posters.

Cancel the Ebay and get your money back.

Then get a couple from Element14 they might cost a bit more but post if free and you can bet they will turn up quickly.



Mick

[6666]

Got hold of some 4012 chips
moodz what are you using for the ICSP board with your pickit2 ?

would you agree these are the right connections ?
28 pin VPP=1, VDD=20/13, VSS=19/8, PGD=17, PGC=18