Analysis this schematic

[mohandes]

I don't have Proteus, not checked PCB. Check if pulses are present on U3 pin6, if not, some error may be in 4538 timing part. If this is OK, and you have no pulse on 4053 pin 11, check transistor, PCB, two 10K resistor values, eventually 4053 (remove it and check pin 11)

Check if pulses are present on U3 pin6
i think it is ok
look at this this is pin6 4053


If this is OK, and you have no pulse on 4053 pin 11.
nearly pin6 is ok(i think) BUT you Careful whether with 4053 and without 4053, look at this (like gnd wave), so i check teransistor,pcb and resistor are ok i am confused.




ok finally i test again all parts and measure all waves by digital oscope(60MHZ)5 day latter,

thanks and regards

[georgi.g.zhelev]

georgi i check all and Q6 and Q7 are correct, but how test the second 4053
thanks

Problem is here ! SEE shematics.

[mohandes]

ok
thanks but my pcb and all teransistor and all conection are true.
just i should say to you i dont use WIMA cap(1UF)and i use MKP cap(certain of in my picture of my pcb)

or maybe the oscope destroyed and have mistake in this ferquency? next time i use digital oscope

again thanks

[Tepco]

As georgi say, problem in timing part. I checked PCB, no visible errors, but recheck for accidental shorts etc. U3 “misfire” this first short pulse due to some reason. Try to isolate problem this way: pulses should look like on gregori's schematic, but 4538 have two complementary outputs, pins 6 \7 and 9\10, measure output, you will see identical signal, just inverted,if just one is wrong, trace that connection or replace chip. But before all this: RECHECK ALL UNUSED PINS,1,4,12,15 TO -10.6V, 3,13 TO GND. If left open, can mess up whole circuit operation. If this is OK, try to probe each MMV, what is on input (5,11) and what you get at output pins to isolate wrong one. Never mind WIMA, company, MKT is just type, fine if value is correct.

[mohandes]

As georgi say, problem in timing part. I checked PCB, no visible errors, but recheck for accidental shorts etc. U3 “misfire” this first short pulse due to some reason. Try to isolate problem this way: pulses should look like on gregori's schematic, but 4538 have two complementary outputs, pins 6 \7 and 9\10, measure output, you will see identical signal, just inverted,if just one is wrong, trace that connection or replace chip. But before all this: RECHECK ALL UNUSED PINS,1,4,12,15 TO -10.6V, 3,13 TO GND. If left open, can mess up whole circuit operation. If this is OK, try to probe each MMV, what is on input (5,11) and what you get at output pins to isolate wrong one. Never mind WIMA, company, MKT is just type, fine if value is correct.

I checked PCB, no visible errors
HI dear tepco,and thanks for check

pulses should look like on gregori's schematic, but 4538 have two complementary outputs, pins 6 \7 and 9\10, measure output
yes i said to georgi before and put the picture of the U3 for pin 10 look(pin10 connectto pin5) :and i think this is my wrong

because have no voltage(very little) and pulse BUT I SHOULD MEASURE ALL PINS YOU SAY AGAIN WITH COIL ,and i say to you and georgi.


RECHECK ALL UNUSED PINS,1,4,12,15 TO -10.6V, 3,13 TO GND/
i am sure correct


try to probe each MMV
it is to hard for me, and dont understand(my means language)???????

Thanks and regards for all helps and guide

[georgi.g.zhelev]

SEEshematics.

[mollax]

Problem is here ! SEE shematics.[ATTACH]24532[/ATTACH]

Problem is here

[mohandes]

HI dear mollax
my schematic is ok(look alexis schematic)
thanks

[mohandes]

Hi mr porkluvr
this isfor you,please check it : http://up.p30parsi.com/out.php/i1628...a-20corect.jpg http://up.p30parsi.com/out.php/i1628...star111web.jpg http://up.p30parsi.com/out.php/i1628...star222web.jpg
http://up.p30parsi.com/out.php/i1628...star333web.jpg http://up.p30parsi.com/out.php/i1628...korigir-tx.jpg http://up.p30parsi.com/out.php/i1628...star444web.jpg
http://up.p30parsi.com/out.php/i1628...pg-2020213.jpg
or
http://megaup.ir/images/cy_chap konam.zip

[porkluvr]

Hi mr porkluvr
this isfor you,please check it...

What I was asking for is the one (1) schematic that you followed when making your PCB.
What you posted are three (3) different schematic versions.

More is not better.

(The link for the zip file did not work).

It's not really important anyway, because what you were asking about is probably an impossibility. You might find a detector to search 5 meters deep (although, don't count on it), and you might find a discriminating detector, but I seriously doubt that you could find a DIY project for something that does both at the same time.

[mohandes]

What I was asking for is the one (1) schematic that you followed when making your PCB.
What you posted are three (3) different schematic versions.

More is not better.

(The link for the zip file did not work).

It's not really important anyway, because what you were asking about is probably an impossibility. You might find a detector to search 5 meters deep (although, don't count on it), and you might find a discriminating detector, but I seriously doubt that you could find a DIY project for something that does both at the same time.

http://www.mediafire.com/?7g707c66yg83rz0

[mohandes]

HI all freind and guru
i replace all ices and check again pcb and measure by multimeter befor than i go to collage,and again write my result
for U2 :
pin 6 and pin10 and pin9have -10.8 volt and pin7 is -0.07volts
and the ferequency for pin6,7,10 are 115hz for pin9 is 135hz and ithink this ic is OK!

for U3:
pin 6 and pin10 and have -10.8 volt , pin9 and pin7 are 0 volts ,IS IT OK??????
and the ferequency JUST pin10 have 115hz , IS IT OK!(i dont this is my problem but how?i check all and not found it,any body knows my error and can tell me please,what do MULTI TURN in pin14?)

thanks just tell me for tomorrow i can give a good answer of me detect.i will go test it tomorrow please help and tell me U3 is ok or no?

[mohandes]

hi all
this is Unclear error for me and until now no body understand it , and i am become tired.
who guys do know how can i solve the error on U3(or second 453
today again i go in collage just pin 10or 9 i think have pulse and pin6,7,9or10i think have not it.
and check all parts pcb ,out put of ne555 and ne 5534 are correct,i an adjustment pps and pw for ne555,and my out put in ne5534 change by multi meter on pin8,and for U2(first 453all out put (pin6,7,9,10)are Square wave and 10 volt.and an adjustment pin6 by
delay volume.

and just pin 9,10 and pin6 4053 are good(pin6 have little error for wave) but the pin11 is very bad.

i wait to one guru say me what is my wrong and if need say to me to put the pictures

thanks

[Davor]

Being a guru means only that you have a lot of posts on the forum, and not that you are skilled in looking at the crystal ball. From what you write I can't say anything useful. I guess no one else can either.

You may try to get familiar with this chip so that you know what to expect.

[mohandes]

ok
thanks