Can pinpointer detecting thin chain?

[Nezocas]

Hi Nupi,

What a load of work I got you ... sorry

I will rewind the wrong windings tightly again .... do not worry about that.
Also seemed to me that I had the whole electrical part as it should be .... but you never know.
C2 must have been easy to change, but the BC not so easy, because its in very tight place ..... also thank´s for that
I see that you have added a LED and piezzo to make the video, nice..... but those parts will not apply to my setup, I will only use the motor.
I will also try to make the coil leads as short as possible to make it really compact

Best regards
Nezocas

[Nupi]

Hi, Nezocas
So much work was not. The circuit was completely right. I will make the video with and without LED and buzzer.
You should take into account that if you the coil place near the circuit the detection point is what restless.
The video will not be good quality with my old camerea, but I hope good enough.


Best regards, nupi

[Nupi]

Okey the video of the NPP of Nezocas is ready.
He is out of focus but you can still see what the intention is.
If someone is irritated by this he can give me a HQ cam. I will be forever grateful to him.

[Nezocas]

WOW

Now it work´s like a charm.
What a "few" wrong turns wound in the wrong direction can make
I would like to see a commercial pinpointer detect up to this distance (probably even exists) but in the house of 50 to 100 euros

This is a really cheaply homemade pointer and easy to make (not for me I was DUMB)

Even if after 5 to 10 minutes of use it starts to get unstable, I think we can restart it to continue detecting

Regards

[Nupi]

It's good to see that you're happy with it, that's my intention.


Don't say that, that you was dumb. You've made a mistake, that's it.
Everyone is mistaken sometimes. Some people do not tell because they are ashamed (for whom?) BS ego.
You should be proud of yourself. You made a great job. Moreover everything worked 100%.
nupi

[Nupi]

Hi, Nezocas.
Tomorrow I'll send you the PP back, okey?
regards, nupi

[Nezocas]

Ok,

I'm not in any hurry

Regards

[chemelec]

Cheap, Multi-Turn Pots

Multi-Turn Pots are Expensive. But 10, 18 or 25 Turn Trimpots are CHEAP.
A Short piece of 1/8 Inch Brass Tubing (From Hobby Shops) can be soldered to the Brass Screw Adjustment on these Trimpots, And than can be fitted with a knob for 1/8" Shafts.

Make sure the Brass Adjustment and the Inside of the Brass tube are Clean.
Carefully Than Pre-Tin the Top of the Brass Screw and partly fill the inside of one end of the tube.

Be Careful to Position it Sraight near the trimpot, than using a Weller Soldering Gun,
Heat the Tube to melt he solder in it, Than place it onto the Screw and Quickly Remove the Iron.

If all goes well it will be Straight and work really good.
On MY FIRST ATTEMPT at this, I had to Re-melt the tube Two times to get it Straight, But still didn't damage the trimpot.

[WM6]

Great solution Gary, thank you for share.

[chemelec]

Nupi, What is the Purpose of C4 & R5 on your Schematic?

Looking at the Output on an Oscilloscope or listening to the output sound, Nothing changes if you Remove them

[chemelec]

Great solution Gary, thank you for share.

Yes I thought it would be good to post it here, Especially since Pinpointer's Usually work better with one.

[Nupi]

Multi-Turn Pots are Expensive. But 10, 18 or 25 Turn Trimpots are CHEAP.
A Short piece of 1/8 Inch Brass Tubing (From Hobby Shops) can be soldered to the Brass Screw Adjustment on these Trimpots, And than can be fitted with a knob for 1/8" Shafts.

Make sure the Brass Adjustment and the Inside of the Brass tube are Clean.
Carefully Than Pre-Tin the Top of the Brass Screw and partly fill the inside of one end of the tube.

Be Careful to Position it Sraight near the trimpot, than using a Weller Soldering Gun,
Heat the Tube to melt he solder in it, Than place it onto the Screw and Quickly Remove the Iron.

If all goes well it will be Straight and work really good.
On MY FIRST ATTEMPT at this, I had to Re-melt the tube Two times to get it Straight, But still didn't damage the trimpot.

Thank you for your positive and constructive contribution.
The Multi-Turn Pots are indeed Expensive and often very large.Your tip is very useful.
I have sometimes used, but I glued the shaft with two component adhesive, because perhaps the problem of the
excessive heat for the trimpot. What I did was supporting the tube so that it lasts longer.I think these tubes are ready on sale.

[Nupi]

Nupi, What is the Purpose of C4 & R5 on your Schematic?

Looking at the Output on an Oscilloscope or listening to the output sound, Nothing changes if you Remove them

I know very well how my circuit works. I made it myself.
With my limited knowledge of the English language (I mean, I understand it pretty well),
but if I want to write it down, then it goes wrong.This applies to all languages. With this handicap, I have to live.
But this is only one small problem. So that was a little bit about myself. I should like to ask you to be understanding,
and not immediately think of what writes the troll again.


I'll try to explain it simply.There are not one but two oscillators. The "Harley" BC560 and IC-4024.
The 4024 is not an oscillator but which are also used here as a relax oscillator beside is a 7-stage binary ripple counter with a clock input.
If you remove C4 and R5 you have no longer a relaxation oscillator.(I hope I have explained well and that you understand)


To explain it well in English you would have to ask Davor.
I do not know how big the knowledge of Qiaozhi is (or someone else) but maybe he will explain it to you, too.


Davor has a thing explained in This thread:


"Basically it is an absorption detector.
Tr1 forms a Hartley oscillator and it is biassed so that it operates in linear regime that is prone to amplitude changes.
When a metal object is introduced to the coil, the amplitude of oscillation is reduced because of the eddy current losses,
but more importantly, the transistor power consumption is enlarged, and thus the emitter voltage gets shifted. This arrangement is not new, and most pinpointers work at this or similar principle. The change in the oscillator working conditions is translated into some sort of indication.
What is new and very good here is the way this working point gets detected It is the role of 4024 that forms a relaxation oscillator with narrow strip of input signal levels that brings it from non-operation to saturation, and in a process it provides a very sensitive indication. It operates on the oscillator's envelope rather than the DC level,
pulse durations are set by pulse counting method, and in a process it provides pulsed audio. Brilliant." #137


"......Your biggest achievement with this pinpointer is the 4024 detector. It outperforms all the envelope detectors by far and wide, and it provides a straightforward beeping tone.
That said, every improvement should start from the 4024 circuit............." #300

[Fabian]

Hi Nupi. I'm working in your PP and I want to know if in necessary to put a white led (for some matter about consumption or something like that), or can I put any color of LED there.

Thanks in advance,

Fabián

[Nupi]

Hi Fabián,
No, it is not necessary to put a white LED.
You can put any color of LED.You have to determine the resistance experimentally for another LED.
Regards, nupi