Delta Pulse

[pigeon]

Hi pigeon
NO,,,,,Because (IGBT) needed control Module to run the gate,,,,,
-we not heard that the IGBT is used for a large coil----where that?????
best time
j.

hi jap

I have seen it on a French website but it does not matter. I suck in electronics but I could make the delta. I have an idea what I can use two IRFP460 aligned to increase the amperage that it helps to stabilize the delta and look deeply objects.

thank you very much for your respect

best time

P.

[jap]

Hi pigeon
- In normal PI MAX current,Higher electrical current to be in the range of 4 AMP depending on the diameter of the wire of the coil and IRF is enough.More AMP from this COIL will be burned and depending on this IRF heats & burned too.
-IRF740 A standard & typical for ~~all projects.
-For use two IRFP640 U NOT nead , U can use one do the work.
-And logical if you are using a battery 12V-7A from where you will get AMP higher than this!!!!!!!!!!!!
^^^^^^TO GO DEEP^^^^^^
-With all of the above taking into account the frequency and BW used.
-Good coil,good project
best time
j.

[pigeon]

Hi pigeon
- In normal PI MAX current,Higher electrical current to be in the range of 4 AMP depending on the diameter of the wire of the coil and IRF is enough.More AMP from this COIL will be burned and depending on this IRF heats & burned too.
-IRF740 A standard & typical for ~~all projects.
-For use two IRFP640 U NOT nead , U can use one do the work.
-And logical if you are using a battery 12V-7A from where you will get AMP higher than this!!!!!!!!!!!!
^^^^^^TO GO DEEP^^^^^^
-With all of the above taking into account the frequency and BW used.
-Good coil,good project
best time
j.

hi jap

thank you for your replay

best time

P.

[hg1898]

This is me I just finished DP, open when a voice, without a voice, is how a matter

[hg1898]

This is me I just finished DP, when the power is on a voice, without a voice, is how a matter

[hg1898]

From the 22K resistor is connected with 555 feet first can get very good sound, without any reaction to the metal, I'm not electronic professional, where should I check, how is this going, who can help me

[Thomas]

[hg1898]

Don't pick up sound, where should I check, this PCB is right

[Thomas]

Check places like this for any solder bridging

[kt315]

Hi everyone,
My DP dont work with LF357, but work with LF351.... Can anyone help me?
Best regards,
Dalibor.

is there output signal on LF357? you can try to use also TL081.

[hg1898]

I checked all the solder bridging left where the line is good, the problem is that, when the power is only a voice, without any sound.
LF357

[pigeon]

hi jap

I search to make a coil 2m for delta how many tours shall a make with adsl cable?but is it going to be better 1m coil. and is it going stable?

thnak you

best time

P.

[pigeon]

hi all

can i replace the adsl cable which is composed of 8 wires with another cable which composed of 10 wires with 1mm diameter each all this is for the purpose of making a coil fpr delta

thank you

best time


P.

[Nicolas]

Hi, this stabilizer is very warm, is it normal ?

[ATTACH]22418[/ATTACH]

Hi Brabra

change the first capacitor 1000uf /6.3v not 35v

it possible send your hex files for PIC18F252
because my hex file not worked with me.
I really not have managed to make it work
and I did not find any solution
I change the PCB, the programmer. anything

[Nicolas]

I wrote the hex into the chip with Pickit2 (i bought the programmer from a hungaryan man - like this http://www.mikroklub.hu/htm/jpg/pickit2c.jpg). This LCD is working with PIC 16f676.

Hi szucs

You can send me the Hex file for LCD discrimination

I use the programmer Pickit2