Tweet
check
-
-
thanksOriginally posted by kt315 View Post
i use ne556 instead of lm556, i have 80mks and perid of this on ne556-5 is 2.5mks ( not 10ms)
and i get in ne556-9 350hz but the it is 17mks not 100-500mks
so ne556 have more DIFFERENCE to lm556 ???
regardsComment
-
no difference. they both are same.
increase C1 and/or R1 valuei use ne556 instead of lm556, i have 80mks and perid of this on ne556-5 is 2.5mks ( not 10ms)
and i get in ne556-9 350hz
increase C3 and/or R4.but the it is 17mks not 100-500mks
VERY seems your nominals of componets ARE WRONG and you DO NOT MEASURE ALL COMPONENTS BEFORE SOLDERING
Comment
-
thanks my delta pulse work but i need to find best adjustment Mr Kt315,for all Tp points .Originally posted by kt315 View Postno difference. they both are same.
increase C1 and/or R1 value
increase C3 and/or R4.
VERY seems your nominals of componets ARE WRONG and you DO NOT MEASURE ALL COMPONENTS BEFORE SOLDERING
regards
my coil is 21m 0.7wire 495mkh.
regardsComment
-
all adjusments will be get automatically. DP was projected for fully dumbs, for a kitchen home worker female. DP has only one (ONE) pot for adjusment - P.P.S.
tune 120Hz for US standart electrical net and 100Hz for EU standart electrical net, this decreases the interference.Comment
-
-
hi dear KT315
i finish that detector and work very good.
but i make turkey board , please put it here for me your design (on board and under board, your pcb my means )
thanks again and best wishes.
regardsComment
-
hi Mohandes, have you P-CAD 2006 installed? I could put a file in it.Comment
-
hiOriginally posted by kt315 View Post
i have P-CAD2002 ,if can not open please put here pdf file( original size of pcb ) and another explain.
regards.
can i make 1.5m*1.5m coil ( and by telephone cable )??? how i calc the inductance ??Comment
-
here .PCB file. I cant say it will open in P-CAD 2002 or not...Comment
-
you are in course... DVD keeps all diggest of soft and formulas how calc the coil... but again...how i calc the inductance ??
I can not take from the forum and put back its again... that is very exhausting for me...
Sizif's Labour... to bring up the rock at mountain again and again that anyway comes down at earth.
so I promise you... everybody will get DVD with all diggest. everybody WHO WANTS.
who does not want will be stay out.
open Gary Chemelec site... http://chemelec.com/Calculators/Calculators.htm
look there A Radial Coil Calculator
Does coils like I use on my metal detector
input your data....
Comment
-
many thanksOriginally posted by kt315 View Post
i will make another
hmmm , i think you make difference dp2 , and I hope it is work . ( are you make it and test it ???)
about the DVD all banks are boycott so i should going to in EXCHANGE STORE to pay you, i will again try.
best wishesComment
-
Yes thank you Kt315Originally posted by kt315 View Post
I managed to open it. A true outline
I wish you good luckComment
-
Originally posted by mohandes View Post
Hi Mohandes I recommend you to use the other type schema for descrimination
https://www.dropbox.com/s/0gum0sw8mlyvt20/PCB.pdf
https://www.dropbox.com/s/hb0ghqcxvn...3%BC%C5%9F.pdf
https://www.dropbox.com/s/d01ijqzmwc...0%C5%9Fema.pdf
https://www.dropbox.com/s/dvfcpozzz9x8hw1/%C5%9Eema.pdf
https://www.dropbox.com/sh/1hlyebnlsoyjsex/GDR816sL80Comment
-
Good evening..
I have designed pcb individually all departments separately for experimentation. believe that this is easier for an improvement and research..
if desired to publish ??..Comment
Comment