Announcement

Collapse
No announcement yet.

My Digital Pulse detector Delta Pulse 3

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hi Biogas
    Delta is Delta, is considered deeper as he accepts the development ,It is development to improve the performance of that every developer has the direction of the development.So each and every one of them will be better if you get a good coil and good components and followed the instructions carefully you will get good results and be better --- As for Pulse StarII is the Original and is considered a reference for comparison.
    best time
    j.

    Comment


    • I have tried that, but it didnt work. Any other ideas?

      Thank you,
      Kerry

      Originally posted by Miata View Post
      Hi,

      push the Escape buttom at startup.

      Regards
      Jürgen

      Comment


      • thank you very much Mr Jap
        But I have another question
        wish pic I will use ( 18f452 of 18f4520 )
        because in the schematic there is 18f4520.
        but at the part list there is 18f452.

        Comment


        • Originally posted by eaglewings35 View Post
          I have tried that, but it didnt work. Any other ideas?

          Thank you,
          Kerry
          Hi eaglewings35
          -read reply#180 see the video Carefully u will know the opening and closing and a scoop with every key and other function.like time 00:57 ,,so on.
          -if error in sw,s connection read reply#174,,,&test.
          best time
          j.

          Comment


          • Originally posted by volcano View Post
            thank you very much Mr Jap
            But I have another question
            wish pic I will use ( 18f452 of 18f4520 )
            because in the schematic there is 18f4520.
            but at the part list there is 18f452.
            Hi volcano
            You can use in the part list PIC 18f452-I/O.
            -By comparison the two pic datasheet the two same,but 18f4520 has other fun. in one pin, it work to.
            -u can test by programming & test
            best time
            j.

            Comment


            • Originally posted by jap View Post
              Hi Biogas
              Delta is Delta, is considered deeper as he accepts the development ,It is development to improve the performance of that every developer has the direction of the development.So each and every one of them will be better if you get a good coil and good components and followed the instructions carefully you will get good results and be better --- As for Pulse StarII is the Original and is considered a reference for comparison.
              best time
              j.
              JAP mANy thanks!

              Comment


              • hello Mr Jap
                please tell me the value of ( -E and +E )
                you look at the picture

                Comment


                • Hi volcano
                  -1- Pin Open in the normal position be zero output +E= 0 shall be zero -2- when it reaches the controlling effort Pin Open be 5v from micro PIC shall be +E=+12volt on a broad.
                  -3- the -E =-10,6V always.
                  -4- THERE IS TWO MODE
                  mode one Pin Open =0 ----> +E=0 ,-E=-10,6V
                  mode two Pin Open =+5V---> +E=+12V ,-E=-10,6V
                  -5- Pin Open Depend on ON/OFF KEY!!!---->enter to PIC ----> out Pin Open L/H
                  I hope I explained the CASE.
                  --IF ERROR TEST PIC!!!!!!!
                  best time
                  j.

                  Comment


                  • Originally posted by jap View Post
                    Hi volcano
                    -1- Pin Open in the normal position be zero output +E= 0 shall be zero -2- when it reaches the controlling effort Pin Open be 5v from micro PIC shall be +E=+12volt on a broad.
                    -3- the -E =-10,6V always.
                    -4- THERE IS TWO MODE
                    mode one Pin Open =0 ----> +E=0 ,-E=-10,6V
                    mode two Pin Open =+5V---> +E=+12V ,-E=-10,6V
                    -5- Pin Open Depend on ON/OFF KEY!!!---->enter to PIC ----> out Pin Open L/H
                    I hope I explained the CASE.
                    --IF ERROR TEST PIC!!!!!!!
                    best time
                    j.
                    thank you Jap

                    So I must install all ICs and also the PIC

                    Comment


                    • Hi volcano
                      in that case u need only pic , key s ,lcd to do test----->on/off--->lcd light
                      Full wishes for the success to complete
                      best time
                      j.

                      Comment


                      • Originally posted by jap View Post
                        Hi volcano
                        in that case u need only pic , key s ,lcd to do test----->on/off--->lcd light
                        Full wishes for the success to complete
                        best time
                        j.
                        what means key s ?

                        and I do not understand the mod on/off

                        Comment


                        • Hi volcano
                          key s=SW1,2,,,SW5!!!!!
                          -mod on/off IN KEY!!!

                          -reply#199
                          -best time
                          j.

                          Comment


                          • thank you very very much Jap
                            you helps all members of forum


                            when I used the keys, the screen is on.
                            But I have a problem ( the PIC can not detect the coil )


                            THANKS

                            Comment


                            • Hi volcano
                              While ( the PIC can not detect the coil ) but coil connected This is normal.
                              Solution:1-He is very sensitive to things inside the place.
                              2-Test must coil a small diameter and lifted a sufficient distance to the up highest.
                              -put photo to glcd while work!!!!
                              best time
                              j.

                              Comment


                              • I ordered the 18F4520 like shown in the schematic and thought that it works, too. After programming there is no output on GLCD (GLCD is tested and ok). Maybe the config is not compatible with this type of PIC so i have to order the 18F452 to check.

                                Comment

                                Working...
                                X