Announcement

Collapse
No announcement yet.

My Digital Pulse detector Delta Pulse 3

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Originally posted by Pasha View Post
    Hi,

    I attached two demo hex to my forum. First demo hex Türkish, second demo hex English.

    Link: http://www.teknolojiekibi.com/yeni/i...p?topic=3797.0



    videos latest version:

    http://www.youtube.com/watch?v=uLPqA...1&feature=plcp


    Regards.
    Thank you, Pasha.
    But there is no menu.
    can we use this hex file for search ?

    Comment


    • Originally posted by volcano View Post
      Thank you, Pasha.
      But there is no menu.
      can we use this hex file for search ?
      demo firmware can detect as full version firmware, but you can't change any parameters, it can't discriminate and this is why it is not possible to use in every condition.
      it is the proof that device is working.

      also there is unique oscilloscope feature in full version that you can't find in any DIY detector, with OSC you can fine tune your dampening slope on GLCD screen.

      regards,

      Comment


      • I want to make last version DP3.

        Anyone can translate this pdf: http://www.teknolojiekibi.com/forumd...%20klavuzu.pdf
        to English version. TIA

        tjmalena

        Comment


        • I may be wrong as my Turkish reading and writing is not that great, so someone can join in if they like and what i have written below presumes you have the document in front of you.

          This section is for the privies version and has been taken of the website it is not part of the current PCB.

          1. In the picture, the components circuled and number 1 (2n2907) should be rotated 180 degrees like in picture
          2. In the picture, the component circled and number 2 (BS250) should be rotated 180 degrees like in the picture.
          3. In the picture, the component circuled and numbed 3 can be replaced with transistor BC557.
          4. Mosfet IRFU024 must be replaced with mosfet 2N7000
          5. BT169D should be used as opposed to SCR.
          6. C13 should be a Tantalum Capacitor
          7. If you intend to use the charger circuit, the two red dots in the picture below must be bridged.
          PAGE 3- Title: consideration when assembling NEW PCB components
          (Writing in Red) The construction should be based on the diagrams provided, abiding to general rules. (Short circuits, drying of resins)

          General Notes: Information regarding LCD Winstar WG12864B
          Contrast resistors: 6,8K 2,2K
          Large size LCD Information Winstar WG12864A
          Contrast resistors: 8,2k 560R
          (Pen writing on maths paper is the wiring diagram for the LCD)

          Page 4
          Title: checks to be made after assembly
          1. Position the PCB like in the picture above
          2. Ensure for the first version 2n2907 and bs250 are installed as in picture.



          Page 5
          3. Next the whole circuit should be checked for 12v to ensure no shot circuits. ( NOTE, IM NOT SURE IF I TRANSLATED THIS PART CORRECTLY)
          4. Now ground the – probe and check to see if there is 12V battery supply like in the picture for the pin show in the picture (NOT SURE IF I TRANSLATED THIS CORRECTLY)

          Page 6
          5. Place you negative probe on the Gnd sine and measure all components as shown in the pictures above, they should show 5V.
          6. Next make the connection like in the picture above.


          Page 10
          7. Ground you negative probe to the - sine and ensure all components in the pictures above show 12v.
          Page 12
          8. Ground your negative probe to the – sine and ensure all components shown in the pictures above show + 1.6~1.8v.
          Next sentence on the same page says: all the above must be checked.

          Page 13
          9. Now the PIC and LCD and all other components can be constructed as in the pictures above.
          10. Looking at the picture above the Grd voltage should be checked to be between +6~7,5v (NOTE MAYE HAVE TRANSLATED THIS PART WRONG)

          Next sentence: If you have not encountered any problems you may now connect PIC and LCD
          Page 14
          11. (NOT sure what it is asking you to do here, I think it says to connect 6.2v to the D6 the 5th pin )
          12. The frequency should be measured here as show in the picture above to show 178~180HZ


          Page 15
          13. The frequency should be measured here like in the picture should be 178~180HZ.
          14. The frequency here should be 178~180 HZ
          15. The frequency measured here should be 178~180HZ
          16. The frequency measured here should be 178~180hz


          If you follow all of these steps you should not encounter a problem. If a problem dose arises you may look at the forum (http://www.teknolojiekibi.com/yeni/i...p?topic=3797.0) to get the necessary information.

          Comment


          • Hi erdin thank you.
            -a Translated good work..
            -U worked an important part ( translate) because it helps everyone who Wants or works in the project and i hope more when a chance.
            best time
            j.

            Comment


            • Originally posted by jap View Post
              Hi erdin thank you.
              -a Translated good work..
              -U worked an important part ( translate) because it helps everyone who Wants or works in the project and i hope more when a chance.
              best time
              j.
              Plessure Jap as you have helped me with a few questions I have had also

              Comment


              • Thank you Mr erdin.
                According to the translation
                We have created a PDF file
                But I do not know How I upload it in the forum

                Comment


                • Originally posted by volcano View Post
                  Thank you Mr erdin.
                  According to the translation
                  We have created a PDF file
                  But I do not know How I upload it in the forum
                  when you click on the ''reply'' tab there is a tab on the next page called '' Go Advanced'' in this page you will find a tab called ''Manage Attachments'' click this tab, from there go to ''Add File'' and click it. next click on 'uploader'' now click on ''Browse'' and you should be able to upload you pdf from there.

                  Comment


                  • Originally posted by erdin View Post
                    when you click on the ''reply'' tab there is a tab on the next page called '' Go Advanced'' in this page you will find a tab called ''Manage Attachments'' click this tab, from there go to ''Add File'' and click it. next click on 'uploader'' now click on ''Browse'' and you should be able to upload you pdf from there.


                    ok

                    this is the the file
                    http://www.mediafire.com/?vl56omtv6x5dmbe

                    Comment


                    • Originally posted by volcano View Post

                      thank you Volcano for this translation

                      Comment


                      • Hi volcano
                        thanks for en.DP3, pdf.
                        best time
                        j.

                        Comment


                        • thanks 4 PDF DP3

                          Comment


                          • thanks to all for responses and encouragement

                            Comment


                            • Hi volcano,

                              thank you for translation.

                              There is a little error at point 11.

                              11. Adjust 6,2V (with Trim 1) at Pin 5 of D6

                              Regards
                              Jürgen

                              Comment


                              • Originally posted by volcano View Post
                                Volcano, There are certain bits that I put notes in that I said I was not sure If I translated correctly, we should wait untile someone fully reads through it just to make sure every thing is translated correctly!

                                Originally posted by Miata View Post
                                Hi volcano,

                                thank you for translation.

                                There is a little error at point 11.

                                11. Adjust 6,2V (with Trim 1) at Pin 5 of D6

                                Regards
                                Jürgen
                                Jurgen, I think your turkish may be better then main, can you read through it and highlight the bits that i may have translated wrong to prevent people from making mistakes.

                                Regards
                                erdin

                                Comment

                                Working...
                                X