Announcement

Collapse
No announcement yet.

Surf PI 1.2 Components

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    Surf PI 1.2 Components

    Hi all. Noob here, would be great if someone could indulge my impatience. The answers to my questions can probably be painstakingly gleaned from the forums, but I am working full time and have had the bright idea of benefitting from beachgoers misfortune over Xmas. I've decided on the surf PI 1.2 as the most practical route and have been poring over images trying to read the exact IC codes of the parts.

    So far, I have chosen:
    NE5534P
    CD4093BE
    CD4066BE
    LM358NG (ON Semi)

    The parts worrying me are:
    NE555D as the kit seems to have TLC55CP. is the NE OK?
    ICL7660. Intersil is very expensive. Kit has TC7660S with 1-12V out. I can get the 1-10V C version through hole, or the S version as SMD. Will either do?

    Are the precise variants of these ICs critical, or will any IC of the same base code (ie 4066) do?

    Only other parts bugging me are the caps. I can't identify the kit poly caps, so will any caps with correct dielectric type, capacitance and voltage do? Any of the eletrolytics need to be low esr?

    I know there were some errors in the original PCB, R18 if I recall. Is there a corrected PCB layout on this site somewhere?

    I know that is a lot of questions, but would be really appreciative if someone could help me out.
    Tags: None
  • #2
    Where did you get the kit from ?

    Comment

    • #3
      EVERYTHING you need right here > http://www.geotech1.com/forums/showt...f-PI-schematic

      And Here > http://www.silverdog.co.uk/ (Andy is a Top Bloke).

      Comment

      • #4
        Originally posted by Clueless View Post
        Hi all. Noob here, would be great if someone could indulge my impatience. The answers to my questions can probably be painstakingly gleaned from the forums, but I am working full time and have had the bright idea of benefitting from beachgoers misfortune over Xmas. I've decided on the surf PI 1.2 as the most practical route and have been poring over images trying to read the exact IC codes of the parts.

        So far, I have chosen:
        NE5534P
        CD4093BE
        CD4066BE
        LM358NG (ON Semi)

        The parts worrying me are:
        NE555D as the kit seems to have TLC55CP. is the NE OK?
        ICL7660. Intersil is very expensive. Kit has TC7660S with 1-12V out. I can get the 1-10V C version through hole, or the S version as SMD. Will either do?

        Are the precise variants of these ICs critical, or will any IC of the same base code (ie 4066) do?

        Only other parts bugging me are the caps. I can't identify the kit poly caps, so will any caps with correct dielectric type, capacitance and voltage do? Any of the eletrolytics need to be low esr?

        I know there were some errors in the original PCB, R18 if I recall. Is there a corrected PCB layout on this site somewhere?

        I know that is a lot of questions, but would be really appreciative if someone could help me out.
        All that parts you have will definately works.

        Comment

        • #5
          Clueless, Which Country are you living in?

          Comment

          • #6
            Living in Port Elizabeth, South Africa.

            Don't have a kit, 6666. Been trying to identify parts from online images as parts list I have found gives generic code for ICs.

            Will check out the links, Sean.

            Thanks everyone.

            Comment

            • #7
              Parts list as issued by SilverDog.

              SURF PI 1.2 Component List:

              C1 = 22nF [Stacked Polyester film (+/-5%)]
              C2 = 1000uF [Eletrolytic 25 Volt]
              C3 = 100nF [Polyester film (+/-10%)]
              C4 = 100nF [Polyester film (+/-10%)]
              C5 = 470nF [Polyester film (+/-10%)]
              C6 = 470nF [Polyester film (+/-10%)]
              C7 = 470nF [Polyester film (+/-10%)]
              C8 = 100nF [Polyester film (+/-10%)]
              C9 = 1nF [Stacked Polyester film (+/-5%)]
              C10 = 1nF [Stacked Polyester film (+/-5%)]
              C11 = 1nF [Stacked Polyester film (+/-5%)]
              C12 = 1nF [Stacked Polyester film (+/-5%)]
              C13 = 220uF [Eletrolytic 10 Volt]
              C14 = 220uF [Eletrolytic 10 Volt]
              C15 = 220uF [Eletrolytic 10 Volt]
              C16 = 100nF [Polyester film (+/-10%)]
              C17 = 220p [Ceramic]
              C18 = 100nF [Polyester film (+/-10%)]

              D1 = 1N4148
              D2 = 1N4148
              D3 = 1N4148
              D6 = 1N4001



              P1 = 100k [Trimmer on PCB]
              P2 = 10k [Tune: Potentiometer]
              P3 = 100k [Delay: Trimmer on PCB]
              P4 = 1k [Volume: Trimmer on PCB or Potentiometer]

              Q1 = 2N3906
              Q2 = IRF9640
              Q6 = MPSA13

              R1 = 100k [1/4 WATT 1% tolerance]
              R2 = 3k3 [1/4 WATT 1% tolerance]
              R3 = 1k5 [1/4 WATT 5% tolerance]
              R4 = 100 [1/4 WATT 5% tolerance]
              R5 = 100 [1/4 WATT 5% tolerance]
              R6 = 390 [1 WATT 5% tolerance]
              R7 = 1k [1/4 WATT 5% tolerance]
              R8 = 1k [1/4 WATT 5% tolerance]
              R9 = 1M [1/4 WATT 5% tolerance]
              R11 = 22k [1/4 WATT 5% tolerance]
              R12 = 10k [1/4 WATT 5% tolerance]
              R13 = 1k [1/4 WATT 5% tolerance]
              R14 = 1k [1/4 WATT 5% tolerance]
              R15 = 220k [1/4 WATT 5% tolerance]
              R16 = 220k [1/4 WATT 5% tolerance]
              R17 = 220k [1/4 WATT 5% tolerance]
              R18 = 47k [1/4 WATT 5% tolerance]
              R20 = 22k [1/4 WATT 5% tolerance]
              R21 = 1k [1/4 WATT 5% tolerance]
              R22 = 100k [1/4 WATT 5% tolerance]
              R23 = 22k [1/4 WATT 5% tolerance]
              R25 = 15k [1/4 WATT 5% tolerance]
              R26 = 51k [1/4 WATT 5% tolerance]
              R28 = 240k [1/4 WATT 5% tolerance]
              R29 = 51k [1/4 WATT 5% tolerance]
              R34 = 33 [1/4 WATT 5% tolerance]
              R35 = 100k [1/4 WATT 5% tolerance]

              U1 = NE555D
              U2 = NE5534P
              U3 = LM358N
              U4 = 4093
              U5 = 78L05
              U6 = ICL7660
              U7 = 4066

              Comment

              • #8
                Homefire, You should post him that Schematic to go along with that Parts List.

                Comment

                • #9
                  Clueless. sent you a pm

                  Comment

                  • #10
                    Thanks Luuk. Just replied by email.

                    Comment

                    • #11
                      I believe this is the Schematic that goes with SilverDogs Kit.
                      Attached Files

                      Comment

                      Previous template Next
                      Working...
                      X